AeroWorks Extra 260 User Manual download pdf (Page 6)

Horizontal Stabilizer with elevator assembly -

pre drilled for control horn mounting, with (10) pin

point hinges (glued) - covered

Rudder -

pre drilled for control horn mounting, with (6)

pin point hinges (not glued) – covered

SUB ASSEMBLIES:

#1:

(1) Fiberglass Cowling—painted with (6) screws

holes

(6) 4-40 x15mm hex style bolts for mounting

cowling

(6) 3mm flat washers for mounting cowling

(6) #6 bonded plastic washers for mounting

cowling.

#2:

(1) 5mm 7075 Aluminum Main Landing Gear --

painted

(2) 5mm AL Axle Bolts

(2) M8 lock nuts

(4) 5mm i.d. Wheel Collars with set-screws

(2) 110mm Dia. Main Wheels (Lite Type)

(4) 4-40x15mm hex style bolts for mounting wheel

pants

(4) 3mm flat washer for mounting wheel pants

(4) 3mm split ring lock washer for mounting wheel

pants

(4) 8-32x25mm hex head bolts for mounting main

landing gear

(4) flat washers for mounting main landing gear

(4) split ring lock washers for mounting main land-

ing gear.

#3:

(2)Wheel Pants—1 Left and 1 Right---Painted

(4) 4-40 blind nuts installed in the wheel pants, 2

per side.

#4:

(1) AL Tail Wheel Assembly -- Large

#5:

(1) 40mm o.d. Anodized Aluminum Tube for wing

joint

(2) 12.5mm o.d. Anodized Aluminum Tube for

stab joint – one front and one rear

(4) 8-32x30mm Hex head bots for wing mounting

(4) #8 bonded washers for wing mounting

(4) 4mm split ring lock washer for wing mounting

(4) 4-40x12mm Hex style head bolts for stab

mounting

(4) #6 bonded washer for stab mounting

#6:

(2) 4-40 2-1/2” two end threaded pushrod with

nuts for elevator

(4) 4-40 3” two end threaded pushrod with nuts for

ailerons

(1) 1.8x300mm threaded pushrod with metal clevis

for throttle

(4) 4-40 ball link for elevator

(8) 4-40 ball link for aileron

#7:

(2) 1x1300mm plastic coated pull-pull steel cable.

(4) 4-40 Metal R/C links with metal clevises and

nuts

(2) 4-40 ball link for rudder

(4) 3.5x5mm brass pull-pull swaging tubes

(8) AL double control horns

(48) T2.6x16mm Phillips head mounting screws

#8:

800cc Gas Fuel Tank assembly

Additional 4mm brass tubes

3 feet of fuel line for gas (large)

#9:

Throttle servo plate

Engine mounting template (DA100 and 3W100)

Engine baffling balsa wood

Plywood cover for the pipe entrance

(8) T2.6x10mm PWA screws for the cover installing

(1) 160x70x6mm foam for the fuel tank.

(2) 300x80x6mm foam for the receiver and battery

(1) 610x20mm Velcro

(2) 610x100x1.6mm balsa wood sheets

(1) 600x300mm D21052 Oracover covering

#10:

(24) 6mm aluminum engine stand offs.

#11:

(2) Skirt for the main landing gear—painted, 1 left

and 1 right

(4) 4-40x6mm Hex style head bolts

(4) 3mm flat washers

(4) 3mm split ring lock washers

#12:

(1) AW - Custom throw meter - measure control

deflection

1 2 3 4 5 6 7 8 9 10 11 ... 74 75

Comments to this Manuals

No comments

AeroWorks Extra 260 User Manual Page 6

Comments to this Manuals

Related products and manuals for Toys & accessories AeroWorks Extra 260